Configuration

This category contains all of our posts that is on configuration of network.

How to Configure Etherchannel Load Balancing in Packet Tracer

Leave a Comment / Configuration / /

EtherChannel employs an algorithm to load-balance traffic effectively among the physical interfaces that form a logical interface in the etherchannel. This ensures that frames within the same flow traverse the network consistently using a designated physical interface. A “flow” is the path from one network device to another. Maintaining the order of frames within a […]

How to Configure Etherchannel Load Balancing in Packet Tracer Read More »

How to Configure PortChannel With Trunk In Cisco Packet Tracer

Leave a Comment / Configuration / /

PortChannel is used to combine multiple physical interfaces into a single logical interface, boosting the bandwidth of a point-to-point connection between two switches. On the other hand, TrunkPort helps to convey traffic from different VLANs over one connection linking two switches. In this post, I will show you how to configure PortChannel with Trunk. We

How to Configure PortChannel With Trunk In Cisco Packet Tracer Read More »

How to Configure LACP Etherchannel on Cisco Switch in Packet Tracer

Leave a Comment / Configuration / /

Link Aggregation Control Protocol (LACP) is the industry-standard protocol, defined by IEEE 802.3ad/802.1AX. It joins multiple physical interfaces connecting two switches or routers into a unified logical interface. This not only increase the overall bandwidth  but also establishes a redundant connection between the network devices. In this post, I will show you how to Configure

How to Configure LACP Etherchannel on Cisco Switch in Packet Tracer Read More »

How to Configure Etherchannel on Cisco Router

Leave a Comment / Configuration / /

Routers, just like switches, have the capability to join multiple physical interfaces into a logical interface referred to as an EtherChannel. While switches extend support for dynamic negotiation protocols such as LACP and PAgP, along with static EtherChannels, routers only support static EtherChannels. In a previous post, we demonstrated how to configure EtherChannel on the

How to Configure Etherchannel on Cisco Router Read More »

How to Configure Layer 3 Etherchannel On Packet Tracer | Configure Etherchannel on layer 3 switch

Leave a Comment / Configuration / /

Layer 3 ether channel, just like Layer 2 ether channel, helps to load balance traffic between multiple physical interfaces, which is configured to be one virtual interface. You have probably learned how to configure layer 2 etherchannels. In this post, I will be showing you how to configure layer 3 etherchannels on the packet tracer.

How to Configure Layer 3 Etherchannel On Packet Tracer | Configure Etherchannel on layer 3 switch Read More »

How To Configure Dynamic Routing In Cisco Packet Tracer

Leave a Comment / Configuration / /

In a local area network (LAN), routers has the knowledge of the routes to host devices within the network. However, in a wide area network (WAN), which typically consist of two or more routers, routers in the network does not know routes to host devices or network addresses beyond those directly connected to its interfaces.

How To Configure Dynamic Routing In Cisco Packet Tracer Read More »

How To Configure HSRP on Layer 3 Switch In Packet Tracer

Leave a Comment / Configuration / /

Hot Standby Routing Protocol (HSRP) is a Cisco proprietary First Hop Redundancy Protocol designed to enhance network reliability by enabling multiple routers to collectively serve as the default gateway for host devices within a subnet. The primary goal of HSRP is to establish redundant connections to the internet for a subnetwork, thereby ensuring a highly

How To Configure HSRP on Layer 3 Switch In Packet Tracer Read More »

How to Configure DHCP Relay Agent on Layer 3 Switch (l3 Switch)

Leave a Comment / Configuration / /

Dynamic Host Configuration Protocol (DHCP) is a protocol that automatically assigns IP addresses to host devices existing on a network from the pool of IP addresses configured on the DHCP server. In small networks, the DHCP server is always in the same subnet with all the DHCP clients; however, when the network grows to two

How to Configure DHCP Relay Agent on Layer 3 Switch (l3 Switch) Read More »

How to Configure DHCP on Layer 3 Switch In Packet Tracer

Leave a Comment / Configuration / /

Dynamic Host Configuration Protocol (DHCP) is a protocol that dynamically assigns IP addresses to any host devices in a network from a pool of IP addresses configured on the DHCP server. Although DHCP is traditionally configured on a router or on a dedicated server, a Layer 3 switch can also serve as a DHCP server.

How to Configure DHCP on Layer 3 Switch In Packet Tracer Read More »

How To Configure Dynamic NAT on Cisco Router In Packet Tracer

Leave a Comment / Configuration / /

This article will guide you on how to Configure Dynamic NAT on Cisco Router using Packet Tracer. Network Address Translation (NAT) is a crucial algorithm utilized to map private IP addresses to public IP addresses, enabling routing over the internet. Due to the substantial increase in the number of internet users over the past few

How To Configure Dynamic NAT on Cisco Router In Packet Tracer Read More »

Scroll to Top